![solar eclipse maestro manual solar eclipse maestro manual](https://cdn.shopify.com/s/files/1/1492/2050/products/oud-eclipse-reed-diffuser-refill-150ml_1200x630.jpg)
- Solar eclipse maestro manual how to#
- Solar eclipse maestro manual install#
- Solar eclipse maestro manual serial#
- Solar eclipse maestro manual software#
# dd if=spl/sunxi-spl.bin of=/dev/sdX bs=1024 seek=8 Now the SD card is formatted and uboot has been compiled we can copy the files to the SD card. The first partition should be vfat as this is FS which U-boot understands Now we have to format the file system on the card:
![solar eclipse maestro manual solar eclipse maestro manual](https://cdn.shopify.com/s/files/1/0060/8052/products/Eclipse-coin-Necklace-1500_1024x1024.jpg)
If there are already partitions on your card do:Ĭreate the first partition, starting from 2048 Once you know which device is your sdcard like sda use this text instead of the sdX name in the references below: You can do this by unplugging your sd card reader and identify which "sd" devices remove from the list. Then press two times you will see a list of your sd devices like sda sdb sdc note that some of these devices may be your hard disk so make sure you know which one is your sd card before you proceed as you can damage your HDD if you choose the wrong sd-device. Plug SD card into your SD card reader and enter in the terminal If you got these two files everything is complete, well done so farįirst we have to make the correct card partitions, this is done with fdisk. Once you have compiled you can see A13-OLinuXino already has support configuration in Allwinner community ubootĪt the end of the process you can check if everything is OK by Ln -s /usr/bin/arm-linux-gnueabi-gcc-4.6 /usr/bin/arm-4.6-linux-gnueabi-gcc To resolve this you can use symbolic links If errors come up that suggest its unable to find arm-4.6-linux-gnueabi-gcc its likely the compilation is expecting the files in a different place or to be named differently to how they were installed. # make a13_olinuxino CROSS_COMPILE=arm-linux-gnueabi. With the following command you can start the uboot build: Then let’s download the uboot sources from GitHub repository, note there are lot of branches but you have to use sunxi branch, the files are about 70 MBĪfter the download you should have a new directory The Allwinner community uboot is maintained by Henrik Nordström aka hno on #freenode irc channel.įirst let’s make the directory where we will build the A13-OLinuXino Linux: Some other tools for building the kernelĪfter the installation you now have all tools to make your very own A13 kernel image.Git which allows you to download from the github which holds source code for some of the system.uboot make image which is required to allow the SD card to book into the linux image.GCC compiler used to compile the kernal.With this line you make sure you have all tools necessary for the A13 kernel and uboot build:
Solar eclipse maestro manual install#
# apt-get install gcc-4.6-arm-linux-gnueabi ncurses-dev uboot-mkimage build-essential git Install the toolchain by typing the following. You will be asked for your password and then your prompt will change to # which means you are now the super user, all future commands should be run in this mode
Solar eclipse maestro manual software#
To install new software you should be with super user rights so do this type in a terminal. You should make sure you have the tools for building the Linux Kernel and install them if you don’t have them. Setup computer for cross compiling and compiling uboot
![solar eclipse maestro manual solar eclipse maestro manual](https://cdn.shopify.com/s/files/1/1839/1569/products/Pre_21.11.191325.jpg)
Solar eclipse maestro manual serial#
Serial adapter for the A13 olinuxino board (Only way to work with uboot as no screen is configured in uboot)
![solar eclipse maestro manual solar eclipse maestro manual](https://eclipse-maps.com/Eclipse-Maps/Gallery/Pages/Annular-total_solar_eclipse_of_2013_November_3_files/HSE2013_Africa_tC4.jpg)
Computer for cross compiling the program and uboot, such as a linux computer
Solar eclipse maestro manual how to#
The following method outlines how to create a program that replaces linux but still relies on u-boot for setup. U-boot sets up the CPU, memory and a few other things then starts Linux executing. The linux operating systems shown in the wiki runs on an SD card however it is booted using u-boot. 1.11 Building quickly and adding new files.1.10 Do something useful, Modify the hello world to set GPIO.1.8 Run the hello world program from the SD card.1.6 The hello world program compilation.1.2 Setup computer for cross compiling and compiling uboot.1 Stand alone program running with uboot.